CAPPUCCINO

Composed of double espresso and hot milk, with the surface topped with foamed milk,
an advanced type which could control more Servo Motors to meet your need for sophisticated Robots and Droids...

Specification


PWM Servo/DC Motors

  • 4 PWM Servo/DC Motors
  • Speed Feedback Control
  • Position Feedback Control
  • Real time control
  • Sequence control
  • PWM: 5 – 95% @ 40Hz – 7000Hz
  • Motor Power: 6 - 24V

UART Steering Servo Motors

  • 255 UART Steering Servo Motors
  • Real time control
  • Sequence control
  • Topology: Bus, Ring, Mess
  • Motor Power: 6 - 12V

Human Machine Interface

  • Touchscreen
  • 7 LEDs

Camellia ARM Controller - CAPPUCCINO

01 POWER This power port is for this ARM Controller and Servo motors/DC motors, 6VDC – 24VDC.
02 Servo Motor/DC Motor Four Servo motor/DC motor control ports.
03 UART Steering Servo Motor UART steering servo motor control port. * seperate 6VDC – 8VDC Power is used.
04 Model Selector Select a Wireless Local Area Network model or a Wide Area Network model.
05 UART Control UART control port.
06 HMI Touchscreen port.
07 LED Six LEDs.


WLAN or WAN

Camellia ARM Controller works as an Access Point, configuring a Wireless Local Area Network.
Wi-Fi is a family of wireless network protocols, based on the IEEE 802.11 family of standards, which are commonly used for local area networking of devices and Internet access, allowing nearby digital devices to exchange data by radio waves.
Wi-Fi uses multiple parts of the IEEE 802 protocol family and is designed to interwork seamlessly with its wired sibling Ethernet. Compatible devices can network through wireless access points to each other as well as to wired devices and the Internet. Wi-Fi most commonly uses the 2.4 gigahertz (120 mm) UHF and 5 gigahertz (60 mm) SHF radio bands; these bands are subdivided into multiple channels. Channels can be shared between networks but only one transmitter can locally transmit on a channel at any moment in time.
Look at your Robots or AIs directly and operate them at home or in the office, even outside.

Camellia ARM Controller works as a Station, connecting to the Internet.
Message Queuing Telemetry Transport is an OASIS standard messaging protocol for the Internet of Things. It is designed as an extremely lightweight publish/subscribe messaging transport that is ideal for connecting remote devices with a small code footprint and minimal network bandwidth.

  • A publish-subscribe with Topic Camellia that transports messages between devices.
  • A publish-subscribe with Topic Camellia@ID that transports messages from Peer to Peer.
Remote control your Robots or AIs from anywhere in Mobiles or PCs anytime via the Internet or 4G/5G cellular signal.

Bluetooth Low Energy

Bluetooth Low Energy Technology is widely used in mobile phones, intelligent watches, health monitors, intelligent apparatus and so on, providing communication between these and mobile phone.
Swarm Network Topology:
- Central: Mobile phones, Pads and Computers.
- Peripheral: Intelligent watches, Health monitors, Intelligent apparatus and so on.
GATT(Generic Attribute Profile)is the protocol.
UUID(Universally Unique IDentifier)is a 128-bit number used to identify information in computer systems.

PWM

Pulse-Width Modulation is a method of reducing the average power delivered by an electrical signal, by effectively chopping it up into discrete parts. The average value of voltage (or current) fed to the load is controlled by turning the switch between supply and load on and off at a fast rate. The longer the switch is on compared to the off periods, the higher the total power supplied to the load.
PWM is particularly suited for running inertial loads such as motors, which are not as easily affected by this discrete switching, because their inertia causes them to react slowly.
The PWM switching frequency has to be high enough not to affect the load, which is to say that the resultant waveform perceived by the load must be as smooth as possible.
The frequency at which the power supply must switch can vary greatly depending on load and application:
PWM signal range from 5% to 95%, with 40Hz to 7kHz, could be output from Camellia ARM Controller as required.

H-Bridge

An H-Bridge is an electronic circuit that switches the polarity of a voltage applied to a load.
Camellia ARM Controller uses this circuit to allow DC motors to run forwards, backwards, stop or break.

UART

A Universal Synchronous Receiver-Transmitter is a computer hardware device for asynchronous serial communication in which the data format and transmission speeds are configurable. It sends data bits one by one, from the least significant to the most significant, framed by start and stop bits so that precise timing is handled by the communication channel. The electric signaling levels are handled by a driver circuit external to the UART.
Two UART ports in Camellia ARM Controller have the same output signal simultaneously; a redundant Bus network or a Ring or a Mess topology network could be configured.

Sequence Control

i = 0;
while (!sequence.isEnd()) {
	start DC motor A;
	...
	set PWM motor B to 90 degree;
	...
	broadcast all UART motor to 26 degree;
	...
	sequence.checkTime();
	...
	if( sequence. onTime()){
		gotoFlash(5);
	}
	i++;
}
print "Welcome to Camellia Café!";

HMI

A Touchscreen enables the user to interact directly with what is displayed, rather than using a mouse, keyboard, or other such.
It is one of Human-Machine Interface. It is an input device and normally layered on the top of an electronic visual display of an information processing system.
Imagine what we can do, now, using Human-to-Machine communications creativity, to help our children to increase their mathematical, physical and chemical knowledge.
Imagine what we can do, now, using Robots or Droids to help us to do everything everywhere in the world.
Imagine what we can do, now, using extremely reliable health monitors connected to local clinics where health workers can serve large populations across geographies using distance medicine.


Internet of Things

Machine to Machine, or M2M is any technology that enables networked devices to exchange information and perform actions without the manual assistance of humans.
Human to Machine, or H2M with inventions which are securing sensors and controllers, is protecting data in motion, improving the performance of connectivity solutions, and instrumenting almost every aspect of our lives.
Peer-to-Peer, or P2P is a distributed application architecture that partitions tasks or workloads between peers. Peers are equally privileged, equipotent participants in the application. In a P2P network, the peers are smart devices which are connected via the Internet. Information can be shared directly between devices in the network without the need of a central server.


Swarm Intelligence

Camellia ARM Controller controls any motors at the same time or in sequence. Each motor or controller communicates with others. All are in the autocracy of a PC/Phone/Pad.
In artificial intelligence and based on the collective behaviour of elements in decentralized and self-organized systems, Swarm Intelligence has significant involvement in the area of Internet of Things to control their operations logically. As IoT-based systems are complex and consist of intelligent objects, powerful decentralized algorithms supported by Swarm Intelligence are used to resolve such complex problems. Algorithms like ant colony optimization, artificial bee colony, and social spider optimization play essential roles in normalizing the IoT processes.
This will help four wheels of a car run respectively, two robot arms work together, three droids play a ballet, and dozens of drones display a 3D firework in the sky…


Application


Get All Mini


Touch ARM